产品详情
查看大图

  • 产品名称：油基荧光渗透液—麦普FP-3Z

  • 产品型号：FP—3Z
  • 产品厂商：苏州麦普
  • 产品文档：
你添加了1件商品 查看购物车
简单介绍：
麦普FP-3Z种类属性 CLASSIFICATION ⚫ 类型：1，去除方法：A 水洗型（非水基）渗透液，灵敏度等级：3 级。 Type 1, Method A Water Washable (Non Water-Based) Penetrants, Sensitivity Level 3 符合标准 SPECIFICATION COMPLIANCE ASME Sec.V、ASTM E165、ASTM E1417、AMS 2644、GB/T 18851.2、ISO 3452-2、 GJB 2367A
详情介绍：
基本信息 GENERAL DESCRIPTION
麦普FP-3Z 是一款 3 级灵敏度的水洗型荧光渗透液，灵敏度高，亮度高，易水洗，可广泛用于各种渗透检测应用中，特别适用于对灵敏度要求较高的高附加值的关键零部件，例如航天航空业中的机匣、叶片等关键零部件。本产品吸收国外先进配方，在综合性能优异的同时兼具环保属性，不含烷基酚/邻苯二甲酸类有毒有害成分。
麦普FP-3Z Fluorescent is level 3 sensitivity Water Washable Penetrants, High sensitivity, high brightness, easy to wash, can be widely used in all kinds of penetration detection applications, especially for high value parts with high sensitivity requirements. This product absorbs foreign advanced formulations, with excellent comprehensive performance and environmental protection properties, and does not contain alkylphenol/phthalic acid toxic and harmful ingredients.
麦普FP-3Z产品特点 Product features
⚫ 高灵敏度高亮度
High sensitivity and brightness
⚫ 易水洗：易水洗去除，背景残留少，信噪比高
Easy to wash: easy to wash off, less background residue, high signal-to-noise ratio
⚫ 粘度适中：快速渗透，渗透剂带走量少，节约渗透剂
Moderate viscosity: fast penetration, less amount of penetration agent to take away, save penetration agent
⚫ 闪点高：大于 110℃，有效降低着火隐患
High flash point: greater than 110℃, effectively reduce the fire hazard
⚫ 挥发慢：超慢挥发速度，可在开口槽中长时间使用，而不用担心渗透剂挥发损耗
Slow volatilization: ultra-slow volatilization speed, can be used for a long time in the open tank, and do not worry about
the volatile loss of the permeant
⚫ 温度适用范围广：低温下不凝固、不析出，高温下不褪色
Wide range of temperature: low temperature does not solidify, do not precipitate, high temperature does not fade
⚫ **环保：气味温和、不含有毒有害成分

The smell is mild and contains no poisonous or harmful ingredients


技术指标 TECHNICAL PROPERTIES



施加方法 METHOD OF APPLICATION
在施加渗透剂之前，工件必须清洁、 干燥、去油、 脂或其他污染物质。水洗型荧光渗透液可通过浸泡、涂刷、倾倒、 常规或静电喷涂等方式施加到工件的待检区域。待检查的区域必须完全覆盖渗透液。
Test parts must be clean, free of all oil, grease or other foreign contaminating substances and dry before penetrant is applied.Water washable penetrants may be applied by immersion, dip, brush or flow-on, conventional or electrostatic spray. The area to be inspected must be completely covered with penetrant.
塑料材质兼容性 PLASTICS COMPATABILITY
可用于尼龙、聚四氟乙烯、乙缩醛、聚丙烯和环氧树脂等塑料材质。但仍然推荐在实际的工件上做相容性实验，避免渗透剂对塑料材质的工件造成影响，例如出现溶胀甚至溶解的现象。
Penetrant materials are typically compatible with nylon, teflon, acetal, polypropylene, and epoxies. However, it is still recommended that the penetrant be evaluated for compatibility on actual test pieces. Penetrants may stain, soften, or even dissolve plastic materials.
渗透/停留时间 PENETRATION - DWELL TIME
渗透时间 10 分钟可以满足大部分的检测需求。但是按照规范要求，渗透过程可能需要更长的时间，这个需要现场根据工艺、零部件以及典型缺陷的类型来确定。
The generally accepted minimum penetration time is 10 minutes, although specific process specifications may require longer dwell times.
温度 TEMPERATURE
水洗型渗透液的操作温度一般应为 0 °C – 50 °C
Water washable penetrants are generally used between 0 °C – 50°C.
去除渗透剂 PENETRANT REMOVAL
渗透液通常可采用水洗喷枪**，水温应为 10 °C – 38 °C

Penetrants are generally removed by water spray with a wash temperature envelope of 10 °C to 38 °C


施加显像剂 DEVELOPER APPLICATION
显像剂可以将缺陷指示放大，提高检测的灵敏度。水基显像剂应在干燥工序前施加，干粉或其他非水基显像剂，
必须在干燥工序后施加。
Developers should be used to maximize the sensitivity of our penetrants. Aqueous developers are applied prior to drying,
dry powder and non-aqueous developers after drying.
警告！在使用水基显像剂时，工件不宜长时间的泡在显像液中，因为这样会对渗透检测的灵敏度产生不利影响。
Warning! Parts should not remain in aqueous developers for any length of time, as the penetrant sensitivity could be impaired.
麦普FP-3Z包装规格 PACKAGING
20 升桶，200 升桶，喷罐
20 and 200 Liters Drum, Aerosol.



姓名：
电话：
您的需求：